��������


BusyBox v1.37.0 (Debian 1:1.37.0-6+b9) built-in shell (ash)
Enter 'help' for a list of built-in commands.

~ # [6necho SNAP-BEGIN; cat /proc/uptime; date -u; cat /proc/device-tree/model; ech
o; uname -a; cat /proc/cmdline
SNAP-BEGIN
191.38 750.11
Thu Jan  1 00:03:42 UTC 1970
JZ08AU Aurora (RAM boot B9B)
Linux aurora 7.2.7-aurora-b9c #9 SMP PREEMPT Sat Oct  3 03:06:50 +06 2026 aarch64 GNU/Linux
earlycon console=tty0 console=ttyMSM0,115200n8 ignore_loglevel loglevel=8 rdinit=/init fbcon=font:6x8 consoleblank=0
~ # echo ---time; cat /run/aurora-modem/time-set; grep -E "TIME|SNTP" /run/auror
a-modem/lifecycle.log | tail -4
---time
cat: can't open '/run/aurora-modem/time-set': No such file or directory
[13.30] TIME probe 1 [QMI_READY]: dms_ms=3247 dms_utc=315964803.247 nitz=none  dms-nitz=- clock=44 -> INVALID (year<2026)
[13.47] TIME probe 2 [SIM_READY]: dms_ms=3417 dms_utc=315964803.417 nitz=none  dms-nitz=- clock=44 -> INVALID (year<2026)
[16.84] TIME probe 3 [RADIO_ONLINE]: dms_ms=6790 dms_utc=315964806.790 nitz=none  dms-nitz=- clock=47 -> INVALID (year<2026)
~ # echo ---modem; /etc/init.d/aurora-modem status
---modem
service: idle
controller: OFF
remoteproc: 4080000.remoteproc offline (/sys/class/remoteproc/remoteproc0) fw=mba.mbn
rmtfs:      pid='' writes_logged=0
qmi dev:    absent  qmi-proxy=''
daemons:    udevd='' dbus='' polkitd='' ModemManager=''
  mm: n/a
wwan up:    0 of 8
routes:     
bam-dmux:   suspended active_ms=0 suspended_ms=190733 control=auto
usb0:       172.16.42.1/24 route-to-host: 172.16.42.2 dev usb0  src 172.16.42.1 
emmc:       writes_completed=0 sectors_written=0
time:       1970-01-01 00:03:42 UTC; set: no; probes: 3
dmesg-errs: 0
~ # echo ---wifi; /etc/init.d/aurora-wifi status; echo ---wifilog; cat /run/auro
ra-wifi/wifi.log; cat /run/aurora-wifi/service.log; echo ---hostapdlog; cat /run
/aurora-wifi/hostapd.log
---wifi
service: idle
remoteproc: a204000.remoteproc running (/sys/class/remoteproc/remoteproc1)
crash=0 watchdog=0 fatal=0
wlan0: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP>  ssid aurora-b8f type AP channel 6 (2437 MHz), width: 20 MHz, center1: 2437 MHz 
hostapd: pid=1705 0 connects, 0 disconnects
[23.01] WCNSS /sys/class/remoteproc/remoteproc1 state=running
[24.87] wlan0 up addr=<MAC> (wcn36xx: firmware WLAN version 'WCN v2.0 RadioPhy vUnknown with 19.2MHz XO')
[25.91] === AP ENABLED ssid=aurora-b8f ch=6 pid=1705 in 16.56s
---wifilog
[9.35] === WIFI START (wait for modem START OK/FAIL up to 300s)
[22.47] modem gate after 13s: [22.04] rollback: full stop
[23.01] WCNSS /sys/class/remoteproc/remoteproc1 state=running
[24.87] wlan0 up addr=<MAC> (wcn36xx: firmware WLAN version 'WCN v2.0 RadioPhy vUnknown with 19.2MHz XO')
[25.91] === AP ENABLED ssid=aurora-b8f ch=6 pid=1705 in 16.56s
[9.35] === WIFI START (wait for modem START OK/FAIL up to 300s)
[22.47] modem gate after 13s: [22.04] rollback: full stop
[23.01] WCNSS /sys/class/remoteproc/remoteproc1 state=running
[24.87] wlan0 up addr=<MAC> (wcn36xx: firmware WLAN version 'WCN v2.0 RadioPhy vUnknown with 19.2MHz XO')
[25.91] === AP ENABLED ssid=aurora-b8f ch=6 pid=1705 in 16.56s
=== service start rc=0 25.92
---hostapdlog
56.152522: VLAN: vlan_set_name_type: SET_VLAN_NAME_TYPE_CMD name_type=2 failed: No error information
56.260276: wlan0: interface state UNINITIALIZED->ENABLED
56.260394: wlan0: AP-ENABLED 
~ # for r in /sys/class/remoteproc/*; do echo "RP $(cat $r/name)=$(cat $r/state)
"; done; iw dev
RP 4080000.remoteproc=offline
RP a204000.remoteproc=running
phy#0
        Interface wlan0
                ifindex 12
                wdev 0x1
                addr <MAC>
                ssid aurora-b8f
                type AP
                channel 6 (2437 MHz), width: 20 MHz, center1: 2437 MHz
                txpower 20.00 dBm
                multicast TXQ:
                        qsz-byt qsz-pkt flows   drops   marks   overlmt hashcol tx-bytes        tx-packets
                        0       0       0       0       0       0       0       0               0
~ # echo ---dmesg-wifi; dmesg | grep -iE "wcn36xx|wcnss|a204000|cfg80211|aurora-
wifi|crash|watchdog"
---dmesg-wifi
[    0.000000] OF: reserved mem: 0x000000008b600000..0x000000008bbfffff (6144 KiB) nomap non-reusable wcnss@8b600000
[    0.967917] remoteproc remoteproc0: releasing a204000.remoteproc
[    0.997334] qcom-wcnss-pil a204000.remoteproc: supply vddcx not found, using dummy regulator
[    1.007298]  a204000.remoteproc.iris: failed to get regulators
[    1.019899] remoteproc remoteproc0: releasing a204000.remoteproc
[    1.050982] qcom-wcnss-pil a204000.remoteproc: supply vddcx not found, using dummy regulator
[    1.059076] remoteproc remoteproc1: a204000.remoteproc is available
[    1.082517] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    1.413433] remoteproc remoteproc1: Direct firmware load for wcnss.mdt failed with error -2
[    1.416180] remoteproc remoteproc1: powering up a204000.remoteproc
[    1.416301] remoteproc remoteproc1: Direct firmware load for wcnss.mdt failed with error -2
[    1.474319] cfg80211: failed to load regulatory.db
[    9.499887] [aurora-wifi] === WIFI START (wait for modem START OK/FAIL up to 300s)
[   22.627081] [aurora-wifi] modem gate after 13s: [22.04] rollback: full stop
[   22.650546] remoteproc remoteproc1: powering up a204000.remoteproc
[   22.656102] remoteproc remoteproc1: Booting fw image wcnss.mdt, size 7260
[   23.142056] remoteproc remoteproc1: remote processor a204000.remoteproc is now up
[   23.158300] [aurora-wifi] WCNSS /sys/class/remoteproc/remoteproc1 state=running
[   23.263446] qcom_wcnss_ctrl remoteproc1:smd-edge.WCNSS_CTRL.-1.-1: WCNSS Version 1.5 1.2
[   23.285578] wcn36xx: mac address: <MAC>
[   24.957953] wcn36xx: firmware WLAN version 'WCN v2.0 RadioPhy vUnknown with 19.2MHz XO' and CRM version 'CNSS-PR-1-4-2-c4-00084'
[   24.972180] wcn36xx: firmware API 1.5.1.2, 41 stations, 2 bssids
[   25.020230] [aurora-wifi] wlan0 up addr=<MAC> (wcn36xx: firmware WLAN version 'WCN v2.0 RadioPhy vUnknown with 19.2MHz XO')
[   26.064437] [aurora-wifi] === AP ENABLED ssid=aurora-b8f ch=6 pid=1705 in 16.56s
~ # echo ---ping; ping -c4 -W3 -I wwan0 77.88.8.8 | tail -2
---ping
ping: sendto: Network is unreachable
PING 77.88.8.8 (77.88.8.8): 56 data bytes
~ # echo ---display; /etc/init.d/aurora-display status; cat /run/aurora-display/
display.log; cat /run/aurora-display/service.log
---display
fb0=panel-mipi-dbid fbcon=bound conn=enabled/On l17_users=1 bl_power=0 bl=1
[7.18] display pipe already enabled (by fbcon takeover) - no unblank needed
[7.20] backlight on -> bl_power=0 actual_brightness=1
[7.27] === DISPLAY READY fb0=panel-mipi-dbid fbcon=bound conn=enabled/On l17_users=1 bl_power=0 bl=1
[7.08] start: fb0=panel-mipi-dbid fbcon=bound conn=enabled/On l17_users=1 bl_power=4 bl=1
[7.11] fbcon bound to fb0
[7.18] display pipe already enabled (by fbcon takeover) - no unblank needed
[7.20] backlight on -> bl_power=0 actual_brightness=1
[7.27] === DISPLAY READY fb0=panel-mipi-dbid fbcon=bound conn=enabled/On l17_users=1 bl_power=0 bl=1
=== service start rc=0 7.27
~ # echo ---consoles; cat /sys/class/tty/console/active; for v in /sys/class/vtc
onsole/vtcon*; do echo "$v $(cat $v/bind) $(cat $v/name)"; done; ls -l /proc/[0-
9]*/fd/0 2>/dev/null | grep -E "ttyMSM0|tty1|console" | sed "s/.* \/proc/\/proc/
"
---consoles
tty0 ttyMSM0
/sys/class/vtconsole/vtcon0 0 (S) dummy device
/sys/class/vtconsole/vtcon1 1 (M) frame buffer device
/proc/1/fd/0 -> /dev/console
/proc/1118/fd/0 -> /dev/ttyMSM0
/proc/627/fd/0 -> /dev/tty1
~ # echo ---getty; hostname; ps | grep -E "[g]etty|[c]ttyhack| sh$"
---getty
aurora
  627 root     getty 0 tty1 linux
 1118 root     sh
~ # echo ---fb; ls -l /dev/dri/card0 /dev/fb0; for f in name bits_per_pixel virt
ual_size stride; do echo "fb0 $f=$(cat /sys/class/graphics/fb0/$f)"; done; cat /
sys/class/drm/card0-SPI-1/enabled /sys/class/drm/card0-SPI-1/dpms
---fb
crw-------    1 root     root      226,   0 Jan  1 00:00 /dev/dri/card0
crw-------    1 root     root       29,   0 Jan  1 00:00 /dev/fb0
fb0 name=panel-mipi-dbid
fb0 bits_per_pixel=16
fb0 virtual_size=128,128
fb0 stride=256
enabled
On
~ # echo ---regs; for r in /sys/class/regulator/regulator.*; do n=$(cat $r/name)
; case $n in l6|l17) echo "$n $(cat $r/state) $(cat $r/microvolts) users=$(cat $
r/num_users)";; esac; done
---regs
l17 enabled 2850000 users=1
l6 enabled 1800000 users=1
~ # echo ---bl; for f in bl_power brightness actual_brightness; do echo "bl $f=$
(cat /sys/class/backlight/backlight/$f)"; done
---bl
bl bl_power=0
bl brightness=1
bl actual_brightness=1
~ # echo ---dmesg-display; dmesg | grep -iE "drm|panel|mipi|spi_qup|78b8000|fbco
n|Console: |frame buffer|backlight|aurora-display|l17"
---dmesg-display
[    0.000000] Kernel command line: earlycon console=tty0 console=ttyMSM0,115200n8 ignore_loglevel loglevel=8 rdinit=/init fbcon=font:6x8 consoleblank=0
[    0.010993] Console: colour dummy device 80x25
[    0.717746] spi_qup 78b8000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.066705] l17: Bringing 0uV into 2850000-2850000uV
[    1.416263] [drm] Initialized panel-mipi-dbi 1.0.0 for spi0.0 on minor 0
[    1.796720] Console: switching to colour frame buffer device 21x16
[    1.860388] panel-mipi-dbi-spi spi0.0: [drm] fb0: panel-mipi-dbid frame buffer device
[    7.233896] [aurora-display] start: fb0=panel-mipi-dbid fbcon=bound conn=enabled/On l17_users=1 bl_power=4 bl=1
[    7.258541] [aurora-display] fbcon bound to fb0
[    7.333314] [aurora-display] display pipe already enabled (by fbcon takeover) - no unblank needed
[    7.354476] [aurora-display] backlight on -> bl_power=0 actual_brightness=1
[    7.418169] [aurora-display] === DISPLAY READY fb0=panel-mipi-dbid fbcon=bound conn=enabled/On l17_users=1 bl_power=0 bl=1
~ # echo ---display-errors; dmesg | grep -iE "drm|panel|mipi|spi0|fbcon|backligh
t|aurora-display" | grep -ciE "err|fail|timeout|warn"
---display-errors
0
~ # echo ---emmc; awk "{print \"w=\"\$5\" s=\"\$7}" /sys/block/mmcblk0/stat
---emmc
w=0 s=0
~ # echo SNAP-END
SNAP-END
~ # [6n