uzbek-plus/logs/uart/emmc1-20260930-005048.log
q 105bef466a Project Aurora: mainline ARM64 Linux on JZ08AU (MSM8916) LTE modem
Sanitized research log, build/reproducibility docs, DTS, kernel configs,
patches, initramfs sources, bootchain migration plans and test logs.
B5 direct boot PASS; B6 modem lifecycle in progress.
No dumps, NV/EFS, vendor firmware or device identifiers included.
2026-09-30 17:23:18 +03:00

567 lines
36 KiB
Text
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

### uartlog start 2026-09-30T00:50:48.817082 /dev/ttyUSB0 115200 8N1
00:50:51.017
00:50:51.017 ~ # reboot -f
00:50:51.417 [ 391.548\xff
00:50:51.417 Format: Log Type - Time(microsec) - Message
00:50:51.418 Log type: B - since boot(excluding boot rom). D - delta
00:50:51.418 B - 165462 - SBL1, Start
00:50:51.418 B - 174277 - pm_device_init, Start
00:50:51.418 D - 11742 - pm_device_init, Delta
00:50:51.418 B - 186050 - boot_flash_init, Start
00:50:51.418 D - 30 - boot_flash_+\x8bB9D - 23210 - boot_config_data_table_init, Delta
00:50:51.418 B - 217922 - sbl1_ddr_set_params, Start
00:50:51.418 B - 219844 - Pre_DDR_clock_init, Start
00:50:51.418 D - 183 - Pre_DDR_clock_init, Delta
00:50:51.418 D - 0 - sbl1_ddr_set_params, Delta
00:50:51.418 B - 238784 - pm_driver_init, Start
00:50:51.418 B - 246196 - batt_voltage=4191
00:50:51.418 D - 7564 - pm_driver_init, Delta
00:50:51.418 B - 246379 - clock_init, Start
00:50:51.418 D - 61 - clock_init, Delta
00:50:51.418 B - \x9a\xaa\xb2\xc2j\x8age Loaded, Delta
00:50:51.418 B - 294691 - sbl1_efs_handle_cookies, Start
00:50:51.418 D - dfs_handle_cookies, End
00:50:51.418 B - 299388 - Image Load, Start
00:50:51.418 KT\xaa\x81Image Loaded, Delta
00:50:51.418 B - 317840 - Image Load, Start
00:50:51.418 j\x92A5\x81Image Loaded, Delta
00:50:51.418 B - 328424 - Image Load, Start
00:50:51.418 K\x92\x82\xba\x82\xcaj
00:50:51.418 AAM 1\x81Image Loaded, Delta
00:50:51.618 B - 349164 - QSEE Execution, Start
00:50:51.618 D - 61 - QSEE Execution, Delta
00:50:51.618 B - 353403 - SBL1, End
00:50:51.618 D - 190229 - SBL1, Delta
00:50:51.618 Android Bootloader - UART_DM Initialized!!!
00:50:51.618 [0] welcome to lk
00:50:51.618
00:50:51.618 [10] platform_init()
00:50:51.618 [10] target_init()
00:50:51.618 \xcd0] MMC card: H4G2a (0.2, 05 2002), manufacturer: 90, OEM: 14a, capacity: 3909091328 bytes
00:50:51.618 [30] SDHC Running in
00:50:51.818
[80] Fastboot mode was forced with compile-time [180] USB init ept @ 0x8f684000
00:50:51.818 [200] udc_start()
00:50:51.818 [300] -- reset --
00:50:51.818 [300] -- portchange --
00:50:52.018 [420] -- reset --
00:50:52.018 [420] -- portchange --
00:50:52.218 [540] fastboot: processing commands
00:50:53.019 [1350] fastboot: getvar:product
00:50:53.019 [1420] fastboot: download:0092f800
00:50:53.219 [1720] fastboot: boot
00:50:53.219 [1720] decompressing kernel image: start
00:50:53.819 [2170] decompressing kernel image: done
00:50:53.819 [2170] qcom,msm-id entry not found
00:50:53.819 [2180] Only one appended non-skales DTB, select it.
00:50:53.819 [2210] Updating device tree: start
00:50:53.819 [2250] kaslr-Seed is added to chosen node
00:50:53.819 [2340] SCM call: 0x84000000 failed with :10000
00:50:54.019 [2340] PSCI v1.0 detected, skipping SMP spin table
00:50:54.019 [2360] Updating device tree+\xa6&\xea\x81booting linux @ 0x80000000, ramdisk @ 0x82000000 (1017983), tags/device tree @ 0x81e00000
00:50:54.019 [2370] Jumping to kernel via monitor
00:50:54.019 [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd030]
00:50:54.019 [ 0.000000] Linux version 7.2.7-aurora-usb1 (q@aiaiai) (aarch64-linux-gnu-gcc (Debian 14.2.0-19) 14.2.0, GNU ld (GNU Binutils for Debian) 2.44) #2 SMP PREEMPT Wed Sep 30 03:43:00 +06 2026
00:50:54.019 [ 0.000000] KASLR enabled
00:50:54.019 [ 0.000000] random: crng init done
00:50:54.019 [ 0.000000] Machine model: JZ08AU Aurora (RAM boot EMMC1)
00:50:54.019 [ 0.000000] earlycon: msm_serial_dm0 at MMIO 0x00000000078b0000 (options '115200n8')
00:50:54.019 [ 0.000000] printk: legacy bootconsole [msm_serial_dm0] enabled
00:50:54.019 [ 0.000000] printk: debug: ignoring loglevel setting.
00:50:54.020 [ 0.000000] OF: reserved mem: 0x0000000086000000..0x00000000862fffff (3072 KiB) nomap non-reusable tz-apps@86000000
00:50:54.020 [ 0.000000] OF: reserved mem: 0x0000000086300000..0x00000000863fffff (1024 KiB) nomap non-reusable smem@86300000
00:50:54.020 [ 0.000000] OF: reserved mem: 0x0000000086400000..0x00000000864fffff (1024 KiB) nomap non-reusable hypervisor@86400000
00:50:54.020 [ 0.000000] OF: reserved mem: 0x0000000086500000..0x000000008667ffff (1536 KiB) nomap non-reusable tz@86500000
00:50:54.020 [ 0.000000] OF: reserved mem: 0x0000000086680000..0x00000000866fffff (512 KiB) nomap non-reusable reserved@86680000
00:50:54.020 [ 0.000000] OF: reserved mem: 0x0000000086700000..0x00000000867dffff (896 KiB) nomap non-reusable rmtfs@86700000
00:50:54.020 [ 0.000000] OF: reserved mem: 0x00000000867e0000..0x00000000867fffff (128 KiB) nomap non-reusable rfsa@867e0000
00:50:54.020 [ 0.000000] cma: Reserved 32 MiB at 0x000000009de00000
00:50:54.020 [ 0.000000] psci: probing for conduit method from DT.
00:50:54.020 [ 0.000000] psci: PSCIv1.0 detected in firmware.
00:50:54.020 [ 0.000000] psci: Using standard PSCI v0.2 function IDs
00:50:54.020 [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
00:50:54.220 [ 0.000000] psci: SMC Calling Convention v1.0
00:50:54.220 [ 0.000000] psci: OSI mode supported.
00:50:54.220 [ 0.000000] psci: [Firmware Bug]: failed to set PC mode: -3
00:50:54.220 [ 0.000000] Zone ranges:
00:50:54.220 [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fffffff]
00:50:54.220 [ 0.000000] DMA32 empty
00:50:54.220 [ 0.000000] Normal empty
00:50:54.220 [ 0.000000] Movable zone start for each node
00:50:54.220 [ 0.000000] Early memory node ranges
00:50:54.220 [ 0.000000] node 0: [mem 0x0000000080000000-0x0000000085ffffff]
00:50:54.220 [ 0.000000] node 0: [mem 0x0000000086000000-0x00000000867fffff]
00:50:54.220 [ 0.000000] node 0: [mem 0x0000000086800000-0x000000009fffffff]
00:50:54.220 [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
00:50:54.220 [ 0.000000] percpu: Embedded 19 pages/cpu s48408 r0 d29416 u77824
00:50:54.220 [ 0.000000] pcpu-alloc: s48408 r0 d29416 u77824 alloc=19*4096
00:50:54.220 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
00:50:54.220 [ 0.000000] Detected VIPT I-cache on CPU0
00:50:54.220 [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR
00:50:54.220 [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI)
00:50:54.220 [ 0.000000] CPU features: detected: ARM erratum 843419
00:50:54.220 [ 0.000000] CPU features: detected: ARM erratum 845719
00:50:54.220 [ 0.000000] CPU features: detected: ARM errata 826319, 827319, 824069, or 819472
00:50:54.220 [ 0.000000] alternatives: applying boot alternatives
00:50:54.220 [ 0.000000] Kernel command line: earlycon console=ttyMSM0,115200n8 ignore_loglevel loglevel=8 rdinit=/init
00:50:54.220 [ 0.000000] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes
00:50:54.220 [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
00:50:54.220 [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
00:50:54.220 [ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB
00:50:54.220 [ 0.000000] software IO TLB: area num 4.
00:50:54.220 [ 0.000000] software IO TLB: SWIOTLB bounce buffer size roundup to 1MB
00:50:54.220 [ 0.000000] software IO TLB: mapped [mem 0x000000009d480000-0x000000009d580000] (1MB)
00:50:54.220 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072
00:50:54.220 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
00:50:54.220 [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
00:50:54.420 [ 0.000000] rcu: Preemptible hierarchical RCU implementation.
00:50:54.420 [ 0.000000] rcu: RCU event tracing is enabled.
00:50:54.420 [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
00:50:54.420 [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
00:50:54.420 [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
00:50:54.420 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
00:50:54.420 [ 0.000000] Root IRQ handler: gic_handle_irq
00:50:54.420 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
00:50:54.420 [ 0.000000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
00:50:54.420 [ 0.000000] arch_timer: cp15 timer running at 19.20MHz (virt).
00:50:54.420 [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
00:50:54.420 [ 0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
00:50:54.420 [ 0.010990] Console: colour dummy device 80x25
00:50:54.420 [ 0.018718] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
00:50:54.420 [ 0.023191] pid_max: default: 32768 minimum: 301
00:50:54.420 [ 0.033785] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
00:50:54.420 [ 0.038210] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
00:50:54.420 [ 0.045597] VFS: Finished mounting rootfs on nullfs
00:50:54.420 [ 0.055508] rcu: Hierarchical SRCU implementation.
00:50:54.420 [ 0.057831] rcu: Max phase no-delay instances is 1000.
00:50:54.420 [ 0.062928] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
00:50:54.420 [ 0.068790] smp: Bringing up secondary CPUs ...
00:50:54.420 [ 0.076885] Detected VIPT I-cache on CPU1
00:50:54.420 [ 0.077063] CPU1: Booted secondary processor 0x0000000001 [0x410fd030]
00:50:54.420 [ 0.077915] Detected VIPT I-cache on CPU2
00:50:54.420 [ 0.078079] CPU2: Booted secondary processor 0x0000000002 [0x410fd030]
00:50:54.420 [ 0.078890] Detected VIPT I-cache on CPU3
00:50:54.420 [ 0.079048] CPU3: Booted secondary processor 0x0000000003 [0x410fd030]
00:50:54.420 [ 0.079183] smp: Brought up 1 node, 4 CPUs
00:50:54.420 [ 0.111995] SMP: Total of 4 processors activated.
00:50:54.420 [ 0.116058] CPU: All CPU(s) started at EL1
00:50:54.420 [ 0.120854] CPU features: detected: 32-bit EL0 Support
00:50:54.420 [ 0.124818] CPU features: detected: CRC32 instructions
00:50:54.420 [ 0.129973] CPU features: detected: PMUv3
00:50:54.621 [ 0.135112] alternatives: applying system-wide alternatives
00:50:54.621 [ 0.140398] Memory: 445132K/524288K available (11840K kernel code, 3336K rwdata, 5668K rodata, 1408K init, 463K bss, 43996K reserved, 32768K cma-reserved)
00:50:54.621 [ 0.145327] devtmpfs: initialized
00:50:54.621 [ 0.173180] posixtimers hash table entries: 2048 (order: 3, 32768 bytes, linear)
00:50:54.621 [ 0.173322] futex hash table entries: 1024 (65536 bytes on 1 NUMA nodes, total 64 KiB, linear).
00:50:54.621 [ 0.180457] 2G module region forced by RANDOMIZE_MODULE_REGION_FULL
00:50:54.621 [ 0.188103] 0 pages in range for non-PLT usage
00:50:54.621 [ 0.188111] 518544 pages in range for PLT usage
00:50:54.621 [ 0.198970] NET: Registered PF_NETLINK/PF_ROUTE protocol family
00:50:54.621 [ 0.204308] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
00:50:54.621 [ 0.210624] thermal_sys: Registered thermal governor 'step_wise'
00:50:54.621 [ 0.210635] thermal_sys: Registered thermal governor 'power_allocator'
00:50:54.621 [ 0.217252] cpuidle: using governor menu
00:50:54.621 [ 0.229678] NET: Registered PF_QIPCRTR protocol family
00:50:54.621 [ 0.233736] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
00:50:54.621 [ 0.238625] ASID allocator initialised with 32768 entries
00:50:54.621 [ 0.245887] Serial: AMBA PL011 UART driver
00:50:54.621 [ 0.253615] CPUidle PSCI: Initialized CPU PM domain topology using OSI mode
00:50:54.621 [ 0.261934] /soc@0/usb@78d9000: Fixed dependency cycle(s) with /soc@0/usb@78d9000/ulpi/phy
00:50:54.621 [ 0.262021] /soc@0/usb@78d9000/ulpi/phy: Fixed dependency cycle(s) with /soc@0/usb@78d9000
00:50:54.621 [ 0.269964] /soc@0/interrupt-controller@b000000: Fixed dependency cycle(s) with /soc@0/interrupt-controller@b000000
00:50:54.621 [ 0.290182] /soc@0/usb@78d9000: Fixed dependency cycle(s) with /soc@0/usb@78d9000/ulpi/phy
00:50:54.621 [ 0.290361] /soc@0/usb@78d9000/ulpi/phy: Fixed dependency cycle(s) with /soc@0/usb@78d9000
00:50:54.621 [ 0.299964] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
00:50:54.621 [ 0.305642] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
00:50:54.621 [ 0.312488] HugeTLB: registered 32.0 MiB page size, pre-allocated 0 pages
00:50:54.621 [ 0.318553] HugeTLB: 0 KiB vmemmap can be freed for a 32.0 MiB page
00:50:54.621 [ 0.325496] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
00:50:54.821 [ 0.331573] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
00:50:54.821 [ 0.338518] HugeTLB: registered 64.0 KiB page size, pre-allocated 0 pages
00:50:54.821 [ 0.344592] HugeTLB: 0 KiB vmemmap can be freed for a 64.0 KiB page
00:50:54.821 [ 0.356811] iommu: Default domain type: Translated
00:50:54.821 [ 0.357601] iommu: DMA domain TLB invalidation policy: strict mode
00:50:54.821 [ 0.363503] pps_core: LinuxPPS API ver. 1 registered
00:50:54.821 [ 0.368647] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
00:50:54.821 [ 0.373781] PTP clock support registered
00:50:54.821 [ 0.382975] EDAC MC: Ver: 3.0.0
00:50:54.821 [ 0.387150] scmi_core: SCMI protocol bus registered
00:50:54.821 [ 0.390860] qcom_scm: convention: smc arm 32
00:50:54.821 [ 0.394508] qcom_scm firmware:scm: SHM Bridge not supported
00:50:54.821 [ 0.399205] qcom_scm firmware:scm: qseecom: found qseecom with version 0x800000
00:50:54.821 [ 0.404355] qcom_scm firmware:scm: qseecom: untested machine, skipping
00:50:54.821 [ 0.412286] FPGA manager framework
00:50:54.821 [ 0.419759] clocksource: Switched to clocksource arch_sys_counter
00:50:54.821 [ 0.421899] VFS: Disk quotas dquot_6.6.0
00:50:54.821 [ 0.427809] VFS: Dquot-cache hash table entries: 512 (4096 bytes)
00:50:54.821 [ 0.440980] NET: Registered PF_INET protocol family
00:50:54.822 [ 0.441156] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
00:50:54.822 [ 0.445554] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
00:50:54.822 [ 0.452011] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
00:50:54.822 [ 0.460245] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
00:50:54.822 [ 0.468260] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear)
00:50:54.822 [ 0.476083] TCP: Hash tables configured (established 4096 bind 4096)
00:50:54.822 [ 0.483056] UDP hash table entries: 256 (order: 2, 16384 bytes, linear)
00:50:54.822 [ 0.489633] NET: Registered PF_UNIX/PF_LOCAL protocol family
00:50:54.822 [ 0.496145] Unpacking initramfs...
00:50:54.822 [ 0.497214] Initialise system trusted keyrings
00:50:54.822 [ 0.505169] workingset: timestamp_bits=46 (anon: 41) max_order=17 bucket_order=0 (anon: 0)
00:50:54.822 [ 0.509901] squashfs: version 4.0 (2009/01/31) Phillip Lougher
00:50:54.822 [ 0.517958] 9p: Installing v9fs 9p2000 file system support
00:50:54.822 [ 0.523930] NET: Registered PF_ALG protocol family
00:50:54.822 [ 0.528926] Key type asymmetric registered
00:50:54.822 [ 0.533662] Asymmetric key parser 'x509' registered
00:50:55.022 [ 0.537866] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 240)
00:50:55.022 [ 0.542530] io scheduler mq-deadline registered
00:50:55.022 [ 0.550175] io scheduler kyber registered
00:50:55.022 [ 0.554481] io scheduler bfq registered
00:50:55.022 [ 0.557334] Freeing initrd memory: 992K
00:50:55.022 [ 0.570660] ledtrig-cpu: registered to indicate activity on CPUs
00:50:55.022 [ 0.571052] IPMI message handler: version 39.2
00:50:55.022 [ 0.575815] ipmi device interface
00:50:55.022 [ 0.580218] ipmi_si: IPMI System Interface driver
00:50:55.022 [ 0.583531] ipmi_si: Unable to find any System Interface(s)
00:50:55.022 [ 0.605417] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
00:50:55.022 [ 0.609210] msm_serial 78b0000.serial: msm_serial: detected port #0
00:50:55.022 [ 0.610594] msm_serial 78b0000.serial: uartclk =\xd8\x82r\xb2\x92\x92\x9a\xb2\xa2\xea\x81msm_serial: console setup on port #0
00:50:55.022 [ 0.622456] printk: legacy console [ttyMSM0] enabled
00:50:55.022 [ 0.622456] printk: legacy console [ttyMSM0] enabled
00:50:55.022 [ 0.631078] printk: legacy bootconsole [msm_serial_dm0] disabled
00:50:55.022 [ 0.631078] printk: legacy bootconsole [msm_serial_dm0] disabled
00:50:55.022 [ 0.644308] msm_serial: driver initialized
00:50:55.022 [ 0.649267] qcom-iommu 1ef0000.iommu: iommu sec: pgtable size: 94208
00:50:55.022 [ 0.668083] loop: module loaded
00:50:55.022 [ 0.691809] spmi_pmic_arb 200f000.spmi: PMIC arbiter version v2 (0x20010000)
00:50:55.022 [ 0.708564] tun: Universal TUN/TAP device driver, 1.6
00:50:55.022 [ 0.709048] VFIO - User Level meta-driver version: 0.3
00:50:55.022 [ 0.717466] rtc-pm8xxx 200f000.spmi:pmic@0:rtc@6000: registered as rtc0
00:50:55.022 [ 0.717676] rtc-pm8xxx 200f000.spmi:pmic@0:rtc@6000: setting system clock to 1970-01-01T00:17:50 UTC (1070)
00:50:55.022 [ 0.724633] i2c_dev: i2c /dev entries driver
00:50:55.222 [ 0.738109] input: pm8941_pwrkey as /devices/platform/soc@0/200f000.spmi/spmi-0/0-00/200f000.spmi:pmic@0:pon@800/200f000.spmi:pmic@0:pon@800:pwrkey/input/input0
00:50:55.222 [ 0.750209] qcom_rng 22000.rng: TRNG support not detected
00:50:55.222 [ 0.753433] clocksource: arch_mmio_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
00:50:55.222 [ 0.758047] arch-timer-mmio b020000.timer: mmio timer running at 19.20MHz (virt)
00:50:55.222 [ 0.773845] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 (0,8000003f) counters available
00:50:55.222 [ 0.777915] cs_system_cfg: CoreSight Configuration manager initialised
00:50:55.222 [ 0.788317] gnss: GNSS driver registered with major 507
00:50:55.222 [ 0.793388] NET: Registered PF_INET6 protocol family
00:50:55.222 [ 0.798665] Segment Routing with IPv6
00:50:55.222 [ 0.802438] In-situ OAM (IOAM) with IPv6
00:50:55.222 [ 0.806008] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
00:50:55.222 [ 0.810526] NET: Registered PF_PACKET protocol family
00:50:55.222 [ 0.815881] 9pnet: Installing 9P2000 support
00:50:55.223 [ 0.820843] Key type dns_resolver registered
00:50:55.223 [ 0.834726] registered taskstats version 1
00:50:55.223 [ 0.834774] Loading compiled-in X.509 certificates
00:50:55.223 [ 0.870304] qcom-smsm smsm: mbox_request_channel: can't parse "mboxes" property
00:50:55.223 [ 0.870359] qcom-smsm smsm: mbox_request_channel: can't parse "mboxes" property
00:50:55.223 [ 0.876468] qcom-smsm smsm: mbox_request_channel: can't parse "mboxes" property
00:50:55.223 [ 0.915146] msm_hsusb 78d9000.usb: Failed to create device link (0x180) with supplier remoteproc for /soc@0/usb@78d9000/ulpi/phy
00:50:55.223 [ 0.930057] s3: Bringing 0uV into 1250000-1250000uV
00:50:55.223 [ 0.930650] s4: Bringing 0uV into 1850000-1850000uV
00:50:55.223 [ 0.934936] l2: Bringing 0uV into 1200000-1200000uV
00:50:55.423 [ 0.939810] l5: Bringing 0uV into 1800000-1800000uV
00:50:55.423 [ 0.944296] l6: Bringing 0uV into 1800000-1800000uV
00:50:55.423 [ 0.947076] gcc-msm8916 1800000.clock-controller: sync_state() pending due to 7824900.mmc
00:50:55.423 [ 0.948619] l7: Bringing 0uV into 1800000-1800000uV
00:50:55.423 [ 0.953533] clk: Disabling unused clocks
00:50:55.423 [ 0.966423] l8: Bringing 0uV into 2900000-2900000uV
00:50:55.423 [ 0.966489] PM: genpd: Disabling unused power \xfc[ 0.980737] l11: Bringing 0uV into 2950000-2950000uV
00:50:55.423 [ 0.980979] l12: Bringing 0uV into 1800000-1800000uV
00:50:55.423 [ 0.985015] l13: Bringing 0uV into 3075000-3075000uV
00:50:55.423 [ 0.991804] Freeing unused kernel memory: 1408K
00:50:55.423 [ 0.994779] Run /init as init process
00:50:55.423 [ 0.998933] with arguments:
00:50:55.423 [ 1.002755] /init
00:50:55.423 [ 1.005719] with environment:
00:50:55.423 [ 1.007948] HOME=/
00:50:55.423 [ 1.010884] TERM=linux
00:50:55.423
00:50:55.423 === AURORA RAM BOOT EMMC1 ===
00:50:55.423 Linux (none) 7.2.7-aurora-usb1 #2 SMP PREEMPT Wed Sep 30 03:43:00 +06 2026 aarch64 GNU/Linux
00:50:55.423 --- model
00:50:55.423 JZ08AU Aurora (RAM boot EMMC1)
00:50:55.423 [ 1.047003] mmc0: SDHCI \xb9\xd1ɽ\xb1\xb1\x95Ɂon24900.mmc [\xb8\x9d\x81ADMA
00:50:55.423 --- c
00:50:55.423 earlycon console=ttyMSM0,115200n8 ignoreٕ\xb1\x81뱕ٕ\xb1\xf58init=/init
00:50:55.623 \x8ar\x8a\xba\x8a\x8a\xca\xca\xea\x81mmc0: Card appears overclocked; req 177770000 Hz, actual 1777701
00:50:55.623 [ 1.188077] mmcblk0: mmc0:0001 H4G2a 3.64 GiB
00:50:55.623 \x82\xc96 p27
00:50:56.223 [ 1.219993] mmcblk0boot0: mmc0:0001 EMMC-RO-SUMMARY devices=30 all_ro=YES
00:50:56.223 [init] EMMC: all 30 block[ 1.857886] [init] EMMC: all 30 block devices read-only (getro=1)
00:50:56.223 devices read-only (getro=1)
00:50:56.223 --- /sys/class/udc:
00:50:56.223 total 0
00:50:56.223 lrwxrwxrwx 1 0 0 0 Jan 1 00:17 ci_hdrc.0 -> ../../devices/platform/soc@0/78d9000.usb/ci_hdrc.0/udc/ci_hdrc.0
00:50:56.223 [ 1.882632] configfs-gadget.aurora gadget.0: HOST MAC <MAC>
00:50:56.223 [ 1.885354] configfs-gadget.aurora gadget.0: MAC <MAC>
00:50:56.223 [ 1.892116] l13: voltage operation not allowed
00:50:56.223 [ 1.898761] [init] usb gadget bound to UDC 'ci_hdrc.0'
00:50:56.223 [init] usb gadget bound to UDC 'ci_hdrc.0'
00:50:56.223 [init] ncm ifname='usb0' dev_addr=<MAC> host_addr=2a[ 1.912936] [init] ncm ifname='usb0' dev_addr=<MAC> host_addr=<MAC>
00:50:56.223 :74:01:b4:5e:28
00:50:56.223 3: usb0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfif[ 1.928408] [init] network: usb0 172.16.42.1/24 up (static, no DHCP)
00:50:56.223 o_fast qlen 1000
00:50:56.223 link/ether <MAC> brd <MAC>
00:50:56.424 inet 172.16.42.1/24 scope global usb0
00:50:56.424 valid_lft forever preferred_lft forever
00:50:56.424 [init] network: usb0 172.16.42.1/24 up (static, no DHCP)
00:50:56.424 === EMMC-INFO-BEGIN
00:50:56.424 name=H4G2a
00:50:56.424 manfid=0x000090
00:50:56.424 oemid=0x014a
00:50:56.424 cid=<EMMC_CID>
00:50:56.424 date=05/2018
00:50:56.424 serial=0x<EMMC_SERIAL>
00:50:56.424 type=MMC
00:50:56.424 size_512=7634944 logical_block=512 bytes=3909091328
00:50:56.424 major minor #blocks name
00:50:56.424
00:50:56.424 179 0 3817472 mmcblk0
00:50:56.424 179 1 65536 mmcblk0p1
00:50:56.424 179 2 512 mmcblk0p2
00:50:56.424 179 3 512 mmcblk0p3
00:50:56.424 179 4 1024 mmcblk0p4
00:50:56.424 179 5 1024 mmcblk0p5
00:50:56.424 179 6 512 mmcblk0p6
00:50:56.424 179 7 512 mmcblk0p7
00:50:56.424 179 8 1024 mmcblk0p8
00:50:56.424 179 9 512 mmcblk0p9
00:50:56.424 179 10 512 mmcblk0p10
00:50:56.424 179 11 512 mmcblk0p11
00:50:56.424 179 12 1024 mmcblk0p12
00:50:56.424 179 13 1536 mmcblk0p13
00:50:56.424 179 14 1536 mmcblk0p14
00:50:56.424 179 15 1024 mmcblk0p15
00:50:56.424 179 16 1 mmcblk0p16
00:50:56.424 179 17 8 mmcblk0p17
00:50:56.424 179 18 10240 mmcblk0p18
00:50:56.424 179 19 32 mmcblk0p19
00:50:56.424 179 20 1536 mmcblk0p20
00:50:56.424 179 21 16 mmcblk0p21
00:50:56.424 179 22 16384 mmcblk0p22
00:50:56.424 179 23 819200 mmcblk0p23
00:50:56.424 179 24 32768 mmcblk0p24
00:50:56.424 179 25 131072 mmcblk0p25
00:50:56.424 179 26 16384 mmcblk0p26
00:50:56.424 179 27 2603455 mmcblk0p27
00:50:56.424 179 32 4096 mmcblk0boot0
00:50:56.424 179 64 4096 mmcblk0boot1
00:50:56.424 === EMMC-GPT-BEGIN (pN name start_512 size_512 ro)
00:50:56.424 mmcblk0p1 modem 131072 131072 1
00:50:56.424 mmcblk0p10 hyp 272384 1024 1
00:50:56.424 mmcblk0p11 hypbak 273408 1024 1
00:50:56.424 mmcblk0p12 pad 274432 2048 1
00:50:56.424 mmcblk0p13 modemst1 276480 3072 1
00:50:56.424 mmcblk0p14 modemst2 279552 3072 1
00:50:56.424 mmcblk0p15 misc 282624 2048 1
00:50:56.424 mmcblk0p16 fsc 284672 2 1
00:50:56.624 mmcblk0p17 ssd 284674 16 1
00:50:56.624 mmcblk0p18 splash 284690 20480 1
00:50:56.624 mmcblk0p19 DDR 393216 64 1
00:50:56.624 mmcblk0p2 sbl1 262144 1024 1
00:50:56.624 mmcblk0p20 fsg 393280 3072 1
00:50:56.624 mmcblk0p21 sec 396352 32 1
00:50:56.624 mmcblk0p22 boot 396384 32768 1
00:50:56.624 mmcblk0p23 system 429152 1638400 1
00:50:56.624 mmcblk0p24 persist 2067552 65536 1
00:50:56.624 mmcblk0p25 cache 2133088 262144 1
00:50:56.624 mmcblk0p26 recovery 2395232 32768 1
00:50:56.824 mmcblk0p27 userdata 2428000 5206911 1
00:50:56.824 mmcblk0p3 sbl1bak 263168 1024 1
00:50:56.824 mmcblk0p4 aboot 264192 2048 1
00:50:56.824 mmcblk0p5 abootbak 266240 2048 1
00:50:56.824 mmcblk0p6 rpm 268288 1024 1
00:50:56.824 mmcblk0p7 rpmbak 269312 1024 1
00:50:56.825 mmcblk0p8 tz 270336 2048 1
00:50:56.825 mmcblk0p9 tzbak 305184 1024 1
00:50:56.825 === EMMC-GPT-END
00:50:56.825 === EMMC-SHA-BEGIN
00:50:57.025 sbl1 mmcblk0p2 6a661ec947c1d935316f9d8731b5314e7502bde5825ebbfc3d2860d081b4096d
00:50:57.425 rpm mmcblk0p6 5a9b857ba6c3af1c848c6e57bbaf9cefcedc3629e5536d27e87b336c67a281fd
00:50:57.825 aboot mmcblk0p4 e4addbf80eb86f6ad8b112e5a3115c7b721bbd2cca8cc109d135aeceb6194482
00:50:58.025 hyp mmcblk0p10 1a963047a4302569da2ddbda726b65c57f5181c0e290ca983dcd2fc529f74555
00:50:58.425 tz mmcblk0p8 8481892fe56fc810e4322b7e6838bf071695e4fc1380c16b21973d7fab325363
00:50:58.625 tzbak mmcblk0p9 c6f7db266a14227ca7e7b0343661089298e4c4320a9522e3e695b5e069e6b4af
00:50:58.625 === EMMC-SHA-END
00:50:58.625 === EMMC-INFO-END
00:50:58.625 === entering shell (exit restarts it) ===
00:50:58.625
00:50:58.625
00:50:58.625 BusyBox v1.37.0 (Debian 1:1.37.0-6+b9) built-in shell (ash)
00:50:58.625 Enter 'help' for a list of built-in commands.
00:50:58.626
00:52:02.844 ~ # mount -t debugfs debugfs /sys/kernel/debug; cat /sys/kernel/debug/mmc0/ios
00:52:02.844 clock: 177770000 Hz
00:52:02.844 actual clock: 177777777 Hz
00:52:02.844 vdd: 17 (2.9 ~ 3.0 V)
00:52:02.844 bus mode: 2 (push-pull)
00:52:02.844 chip select: 0 (don't care)
00:52:02.844 power mode: 2 (on)
00:52:02.844 bus width: 3 (8 bits)
00:52:02.844 timing spec: 9 (mmc HS200)
00:52:02.844 signal voltage: 1 (1.80 V)
00:52:02.845 driver type: 0 (driver type B)
00:52:05.845 ~ # dmesg | grep -iE "mmc|sdhci"
00:52:05.845 [ 0.000000] Machine model: JZ08AU Aurora (RAM boot EMMC1)
00:52:05.845 [ 0.947076] gcc-msm8916 1800000.clock-controller: sync_state() pending due to 7824900.mmc
00:52:05.845 [ 1.047003] mmc0: SDHCI controller on 7824900.mmc [7824900.mmc] using ADMA
00:52:05.846 [ 1.171199] mmc0: Card appears overclocked; req 177770000 Hz, actual 177777777 Hz
00:52:05.846 [ 1.171251] mmc0: Card appears overclocked; req 177770000 Hz, actual 177777777 Hz
00:52:05.846 [ 1.180115] mmc0: new HS200 MMC card at address 0001
00:52:05.846 [ 1.188077] mmcblk0: mmc0:0001 H4G2a 3.64 GiB
00:52:05.846 [ 1.203477] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27
00:52:05.846 [ 1.219993] mmcblk0boot0: mmc0:0001 H4G2a 4.00 MiB
00:52:05.846 [ 1.229490] mmcblk0boot1: mmc0:0001 H4G2a 4.00 MiB
00:52:05.846 [ 1.237006] mmcblk0rpmb: mmc0:0001 H4G2a 4.00 MiB, chardev (508:0)
00:52:05.846 [ 1.857886] [init] EMMC: all 30 block devices read-only (getro=1)
00:52:08.847 ~ # for p in /sys/class/block/mmcblk0p*; do n=$(sed -n s/^PARTNAME=//p $p/uevent
00:52:08.847 ); case $n in DDR|sec) echo SHA $n $(basename $p) $(sha256sum /dev/$(basename $p
00:52:08.847 )|cut -c1-64);; esac; done
00:52:11.848 ~ # for d in /dev/mmcblk0 /dev/mmcblk0p* /dev/mmcblk0boot*; do printf "%s=%s " $
00:52:11.848 (basename $d) $(blockdev --getro $d); done; echo; cat /sys/block/mmcblk0/stat
00:52:12.048 mmcblk0=1 mmcblk0p1=1 mmcblk0p10=1 mmcblk0p11=1 mmcblk0p12=1 mmcblk0p13=1 mmcblk0p14=1 mmcblk0p15=1 mmcblk0p16=1 mmcblk0p17=1 mmcblk0p18=1 mmcblk0p19=1 mmcblk0p2=1 mmcblk0p20=1 mmcblk0p21=1 mmcblk0p22=1 mmcblk0p23=1 mmcblk0p24=1 mmcblk0p25=1 mmcblk0p26=1 mmcblk0p27=1 mmcblk0p3=1 mmcblk0p4=1 mmcblk0p5=1 mmcblk0p6=1 mmcblk0p7=1 mmcblk0p8=1 mmcblk0p9=1 mmcblk0boot0=1 mmcblk0boot1=1
00:52:12.048 41 0 8424 75 0 0 0 0 0 72 75 0 0 0 0 0 0
00:52:40.456 ~ # cat /sys/class/block/mmcblk0p19/uevent
00:52:40.456 MAJOR=179
00:52:40.456 MINOR=19
00:52:40.456 DEVNAME=mmcblk0p19
00:52:40.456 DEVTYPE=partition
00:52:40.456 DISKSEQ=25
00:52:40.456 PARTN=19
00:52:40.456 PARTNAME=DDR
00:52:40.456 PARTUUID=708298a7-c75e-4858-f9bd-1d8e94857b8a
00:52:43.457 ~ # sha256sum /dev/mmcblk0p19; echo rc=$?
00:52:46.458 cat /sys/class/block/mmcblk0p21/uevent
00:52:46.458 MAJOR=179
00:52:46.458 MINOR=21
00:52:46.458 DEVNAME=mmcblk0p21
00:52:46.458 DEVTYPE=partition
00:52:46.458 DISKSEQ=25
00:52:46.458 PARTN=21
00:52:46.458 PARTNAME=sec
00:52:46.458 PARTUUID=057d8b8f-2449-5ddf-5684-35cf05e7e8fb
00:52:49.459 ~ # sha256sum /dev/mmcblk0p21; echo rc=$?
00:53:20.668 sha256sum /dev/mmcblk0p19 /dev/mmcblk0p21 > /tmp/ddrsec.txt 2>&1; echo rc=$?
00:53:20.668 >> /tmp/ddrsec.txt
00:53:23.669 cat /tmp/ddrsec.txt
00:53:23.669 c35020473aed1b4642cd726cad727b63fff2824ad68cedd7ffb73c7cbd890479 /dev/mmcblk0p19
00:53:23.669 3b1cae78981f065f648ee33b048de38004569dacb2ae4a3093404eb1b5586985 /dev/mmcblk0p21
00:53:23.669 rc=0
00:53:26.670 ~ # dmesg | tail -5
00:53:26.670 [ 1.885354] configfs-gadget.aurora gadget.0: MAC <MAC>
00:53:26.670 [ 1.892116] l13: voltage operation not allowed
00:53:26.670 [ 1.898761] [init] usb gadget bound to UDC 'ci_hdrc.0'
00:53:26.670 [ 1.912936] [init] ncm ifname='usb0' dev_addr=<MAC> host_addr=<MAC>
00:53:26.670 [ 1.928408] [init] network: usb0 172.16.42.1/24 up (static, no DHCP)
00:53:52.078 ~ # ping -c 5 172.16.42.2 > /tmp/ping.txt 2>&1; tail -2 /tmp/ping.txt
00:53:56.279 5 packets transmitted, 5 packets received, 0% packet loss
00:53:56.279 round-trip min/avg/max = 1.899/2.290/2.706 ms
00:53:59.080 ~ # cat /sys/block/mmcblk0/stat > /tmp/stat.txt; for p in /sys/block/mmcblk0/mmc
00:53:59.080 blk0p*; do echo $(basename $p) $(cat $p/stat); done >> /tmp/stat.txt; awk "{w+=\
00:53:59.280 $5; s+=\$7} END {print \"TOTAL writes_completed=\" w \" sectors_written=\" s}" /
00:53:59.281 tmp/stat.txt
00:53:59.281 TOTAL writes_completed=72 sectors_written=0
00:54:06.082 ~ # head -1 /tmp/stat.txt
00:54:06.283 45 0 8616 82 0 0 0 0 0 76 82 0 0 0 0 0 0
01:00:01.997 ~ #
01:00:02.197 ~ # sync; echo POWEROFF-TEST; poweroff -f
01:00:02.197 POWEROFF-TEST
01:00:02.597 [ \xff
01:00:02.597 Format: Log Type - Time(microsec) - Message
01:00:02.597 Log type: B - since boot(excluding boot rom). D - delta
01:00:02.597 B - 156678 - SBL1, Start
01:00:02.597 B - 165493 - pm_device_init, Start
01:00:02.597 D - 11712 - pm_device_init, Delta
01:00:02.597 B - 177235 - boot_flash_init, Start
01:00:02.597 D - 0 - boot_flash_+\x8bB=D - 23210 - boot_config_data_table_init, Delta
01:00:02.597 B - 209169 - sbl1_ddr_set_params, Start
01:00:02.597 B - 211060 - Pre_DDR_clock_init, Start
01:00:02.597 D - 213 - Pre_DDR_clock_init, Delta
01:00:02.597 D - 0 - sbl1_ddr_set_params, Delta
01:00:02.597 B - 230031 - pm_driver_init, Start
01:00:02.597 B - 237442 - batt_voltage=4193
01:00:02.597 D - 7594 - pm_driver_init, Delta
01:00:02.597 B - 237625 - clock_init, Start
01:00:02.597 D - 61 - clock_init, Delta
01:00:02.598 B - \xaaLM\xa6j\x8a\x9d\x95\x81Loaded, Delta
01:00:02.598 B - 285907 - sbl1_efs_handle_cookies, Start
01:00:02.598 D - \x90\x99\xcd}\xa1\x85\xb9\x91\xb1\x95}\x8d\xbd\xbd\xad\xa5\x95ͱ End
01:00:02.598 B - 290634 - Image Load, Start
01:00:02.598 K QHEE Image Loaded, Delta
01:00:02.598 B - 309087 - Image Load, Start
01:00:02.598 j\x92A5\x81Image Loaded, Delta
01:00:02.598 B - 319670 - Image Load, Start
01:00:02.598 - 20740 - APPSBL Image Loaded, Delta
01:00:02.598 B - 340380 - QSEE Execution, Start
01:00:02.798 D - 91 - QSEE Execution, Delta
01:00:02.798 B - 344619 - SBL1, End
01:00:02.798 D - 190229 - SBL1, Delta
01:00:02.798 Android Bootloader - UART_DM Initialized!!!
01:00:02.798 [0] welcome to lk
01:00:02.798
01:00:02.798 [10] platform_init()
01:00:02.798 [10] target_init()
01:00:02.798 \xcc0] MMC card: H4G2a (0.2, 05 2002), manufacturer: 90, OEM: 14a, capacity: 3909091328 bytes
01:00:02.798 [30] SDHC Running in
01:00:02.998
[80] Fastboot mode was forced with compile-time [180] USB init ept @ 0x8f684000
01:00:02.998 [200] udc_start()
01:00:02.998 [300] -- reset --
01:00:02.998 [300] -- portchange --
01:00:03.198 [420] -- reset --
01:00:03.198 [420] -- portchange --
01:00:03.198 [540] fastboot: processing commands
01:02:25.837
01:02:25.837 Format: Log Type - Time(microsec) - Message
01:02:25.837 Log type: B - since boot(excluding boot rom). D - delta
01:02:25.837 B - 124257 - SBL1, Start
01:02:25.837 B - 131241 - pm_device_init, Start
01:02:25.837 D - 11224 - pm_device_init, Delta
01:02:25.838 B - 142526 - boot_flash_init, Start
01:02:25.838 D - 0 - boot_flash_i+\x8bB
=D - 23241 - boot_config_data_table_init, Delta
01:02:25.838 B - 174460 - sbl1_ddr_set_params, Start
01:02:25.838 B - 176381 - Pre_DDR_clock_init, Start
01:02:25.838 D - 183 - Pre_DDR_clock_init, Delta
01:02:25.838 D - 0 - sbl1_ddr_set_params, Delta
01:02:25.838 B - 195322 - pm_driver_init, Start
01:02:26.038 B - 202733 - batt_voltage=4192
01:02:26.038 D - 7564 - pm_driver_init, Delta
01:02:26.038 B - 202947 - clock_init, Start
01:02:26.038 D - 30 - clock_init, Delta
01:02:26.038 B - \xca\xa6\xaa\x9a\xbaj\x8aXVb\xbd\x85\x91\x95\x91\xb1 Delta
01:02:26.038 B - 252204 - sbl1_efs_handle_cookies, Start
01:02:26.038 D - \xfa\x95\x99\xcd}\xa1\x85\xb9\x91\xb1\x95}\x8d\xbd\xbd\xad\xa5\x95ͱ End
01:02:26.038 B - 256901 - Image Load, Start
01:02:26.038 - \x8a!\x81Image Loaded, Delta
01:02:26.038 B - 275354 - Image Load, Start
01:02:26.038
\x92j\x92A5\x81Image Loaded, Delta
01:02:26.038 B - 285907 - Image Load, Start
01:02:26.038 j\x92\x82\xba\x82\xcaj
01:02:26.038 AAM 1\x81Image Loaded, Delta
01:02:26.038 B - 306647 - QSEE Execution, Start
01:02:26.038 D - 61 - QSEE Execution, Delta
01:02:26.038 B - 310886 - SBL1, End
01:02:26.038 D - 188886 - SBL1, Delta
01:02:26.038 Android Bootloader - UART_DM Initialized!!!
01:02:26.038 [0] welcome to lk
01:02:26.038
01:02:26.038 [10] platform_init()
01:02:26.038 [10] target_init()
01:02:26.038 \xab&\xea\x81MMC card: H4G2a (0.2, 05 2002), manufacturer: 90, OEM: 14a, capacity: 3909091328 bytes
01:02:26.239 [30] SDHC Running in
01:02:26.239
[80] Fastboot mode was forced with compile-time fj[180] USB init ept @ 0x8f684000
01:02:26.239 [200] udc_start()
01:02:26.439 [300] -- reset --
01:02:26.439 [300] -- portchange --
01:02:26.439 [420] -- reset --
01:02:26.439 [420] -- portchange --
01:02:26.639 [540] fastboot: processing commands
01:02:46.845 [20750] -- reset --
01:02:46.845 [20750] EP1/out FAIL nfo=40 pg0=8f679e80
01:02:46.845 [20750] -- portchange --
01:02:46.845 [20760] usb_read() transaction failed
01:02:46.845 [20760] fastboot: oops!
01:02:47.045 [20860] -- reset --
01:02:47.045 [20870] -- portchange --
01:02:47.045 [20990] fastboot: processing commands
01:02:59.648 [33490] fastboot: getvar:product
01:10:22.376 [476330] fastboot: getvar:product