dddc11e57b
B8A audit, B8B Pronto remoteproc (fixed wcnss_mem 0x8b600000), B8C stock NV (fixes Pronto startup watchdog), B8D cfg80211/mac80211/wcn36xx -> phy0/wlan0, B8E wlan0 up + WPA2/CCMP test AP, B8F eMMC cache 857c9c30 with aurora-wifi autostart: 3/3 class-A cold boots, AP up 76-94 s after power-on, LTE unaffected. PSK, NV and PSK-bearing images are not published.
153 lines
4.7 KiB
Text
153 lines
4.7 KiB
Text
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* Project Aurora — JZ08AU-XPA-7J-R3 (MSM8916, 512 MB, ST7735S SPI panel).
|
|
* B8B (RAM test only): bam1 + Pronto/WCNSS remoteproc + Iris (no WLAN stack, no NV).
|
|
* Base was RAM-BOOT MODEM1: EMMC1 + MPSS remoteproc (native Aurora firmware, rmtfs -r). No BAM-DMUX/WWAN/WCNSS. Everything that could touch
|
|
* storage, radios or power management is explicitly disabled.
|
|
*
|
|
* Hardware facts from stock Aurora dtb_01 (see NOTES.md S2.1/S12):
|
|
* console = BLSP1 UART2 serial@78b0000, GPIO4 (TX) / GPIO5 (RX), 115200 8N1.
|
|
* RAM size (memory@80000000 reg) is filled in by lk2nd from SMEM.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "msm8916-pm8916.dtsi" /* + RPM regulators (USB PHY L7/L13) */
|
|
|
|
/ {
|
|
model = "JZ08AU Aurora (RAM boot B8B)";
|
|
compatible = "jz08au,aurora", "qcom,msm8916";
|
|
chassis-type = "embedded";
|
|
|
|
aliases {
|
|
serial0 = &blsp_uart2;
|
|
mmc0 = &sdhc_1; /* eMMC */
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
/*
|
|
* B8B: WCNSS/Pronto carve-out at the stock Aurora address. Stock dtb_01 "peripheral_mem"
|
|
* (pronto PIL region) = 0x8b600000 size 0x600000; wcnss.mdt is linked at 0x8b600000.
|
|
* Directly follows mpss_mem (0x86800000 + 0x4e00000 = 0x8b600000) -> no overlap.
|
|
* Same fixed-address pattern as upstream msm8916-longcheer-l8150.dts.
|
|
*/
|
|
reserved-memory {
|
|
/delete-node/ wcnss;
|
|
|
|
wcnss_mem: wcnss@8b600000 {
|
|
reg = <0x0 0x8b600000 0x0 0x600000>;
|
|
no-map;
|
|
};
|
|
};
|
|
};
|
|
|
|
&blsp_uart2 {
|
|
pinctrl-0 = <&blsp_uart2_console_default>;
|
|
pinctrl-1 = <&blsp_uart2_console_sleep>;
|
|
pinctrl-names = "default", "sleep";
|
|
status = "okay";
|
|
};
|
|
|
|
/* --- RAM boot MODEM1 safety: no SD slot, no Wi-Fi, no modem data plane --- */
|
|
/* sdhc_1 (eMMC): enabled below, READ-ONLY enforced by initramfs (blockdev --setro) */
|
|
&sdhc_2 { status = "disabled"; };
|
|
/* usb: see peripheral block below */
|
|
/* mpss: enabled below */
|
|
&bam_dmux { status = "okay"; }; /* B4b1: data-plane mux driver (no bearer) */
|
|
&bam_dmux_dma { status = "okay"; };
|
|
/* wcnss: enabled below (B8B) */
|
|
|
|
/*
|
|
* USB peripheral only (ChipIdea ci-hdrc + qcom,usb-hs-phy-msm8916, upstream bindings).
|
|
* Stock Aurora: HSUSB_1p8 = L7 1.8 V, HSUSB_3p3 = L13 3.075 V, otg-control = 2 (PMIC VBUS detect),
|
|
* PHY init-seq identical to upstream. VBUS detect via PM8916 USB_IN (as on JZ02). No host, no role switch.
|
|
*/
|
|
&pm8916_usbin {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb {
|
|
dr_mode = "peripheral";
|
|
extcon = <&pm8916_usbin>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_hs_phy {
|
|
extcon = <&pm8916_usbin>;
|
|
};
|
|
|
|
/*
|
|
* Internal eMMC (stock: bootdevice=7824900.sdhci, qcom,bus-width 8, nonremovable,
|
|
* vdd = 8916_l8 2.85-2.9 V, vdd-io = 8916_l5 1.8 V). Upstream msm8916.dtsi already provides
|
|
* bus-width = <8>, non-removable, mmc-ddr-1_8v (no HS200 = conservative), sdc1 pinctrl;
|
|
* msm8916-pm8916.dtsi provides vmmc = pm8916_l8, vqmmc = pm8916_l5. Only enable it here.
|
|
*/
|
|
&sdhc_1 {
|
|
status = "okay";
|
|
};
|
|
|
|
/*
|
|
* MPSS (modem) remoteproc, native Aurora firmware from the RO-mounted modem FAT.
|
|
* mpss_mem: stock Aurora "modem_adsp_region" base 0x86800000 size 78 MiB (0x4e00000);
|
|
* Aurora modem.mdt load span 0x86800000..0x8b300000 (75 MiB), same as stock PIL log.
|
|
* mba_mem: upstream dynamic 1 MiB. pll-supply (pm8916_l7), cx/mx rpmpd from msm8916(-pm8916).dtsi.
|
|
* Driver has auto_boot = false: MSS starts only when rmtfs (-s) requests it.
|
|
* BAM-DMUX stays disabled (no data plane at this stage).
|
|
*/
|
|
&mba_mem {
|
|
status = "okay";
|
|
};
|
|
|
|
&mpss_mem {
|
|
reg = <0x0 0x86800000 0x0 0x4e00000>;
|
|
status = "okay";
|
|
};
|
|
|
|
&mpss {
|
|
pinctrl-0 = <&sim_ctrl_default>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
/*
|
|
* SIM routing as found on stock Aurora (dtb_01 gpio-leds default-state and live
|
|
* Android /sys/kernel/debug/gpio): gpio1 (sim3_switch) high, gpio20 (sim_hotdet),
|
|
* gpio22 (sim1_switch), gpio23 (sim2_switch) low. Passive routing only.
|
|
*/
|
|
&tlmm {
|
|
sim_ctrl_default: sim-ctrl-default-state {
|
|
sim-low-pins {
|
|
pins = "gpio20", "gpio22", "gpio23";
|
|
function = "gpio";
|
|
bias-disable;
|
|
output-low;
|
|
};
|
|
|
|
sim-high-pins {
|
|
pins = "gpio1";
|
|
function = "gpio";
|
|
bias-disable;
|
|
output-high;
|
|
};
|
|
};
|
|
};
|
|
|
|
/*
|
|
* B8B: Pronto (WCNSS) remoteproc + Iris RF. Firmware = default "wcnss.mdt" from /firmware/image (RO FAT).
|
|
* Supplies come from msm8916-pm8916.dtsi and match stock dtb_01: vddpx/vddxo = L7 1.8 V, vddrfa = S3,
|
|
* vddpa = L9 3.3 V, vdddig = L5 1.8 V.
|
|
* Iris compatible: stock DT has none (generic qcom,wcnss_wlan + qcom,has-autodetect-xo). Stock voltages exclude
|
|
* WCN3660 (vddpa 2.9-3.0 V, vdddig 1.2 V); WCN3620 vs WCN3680 have identical vregs (differ in 48 MHz XO);
|
|
* stock Pronto FW caps lack DOT11AC -> WCN3620 (controlled hypothesis, see logs/b8/b8b).
|
|
* WLAN/cfg80211/wcn36xx are NOT in this kernel; wcnss_ctrl NV download is expected to fail (no NV in rootfs).
|
|
*/
|
|
&wcnss {
|
|
status = "okay";
|
|
};
|
|
|
|
&wcnss_iris {
|
|
compatible = "qcom,wcn3620";
|
|
};
|